column By: Jeff “Tank” Hoover | December, 26

Sixgunners are traditional at heart. While we may not be card-carrying members of the flat earth society, it wouldn’t surprise me if quite a few of us were members of the Flat-Top Society, if such an organization existed. Perhaps we need to start one?

Chambered in 44 Magnum, the Ruger 44 Magnum Flat Top was a stoutly-chambered pistol in a lightweight gun. It had an aluminum grip frame and came in 6.5-, 7.5- and 10.5-inch barrel lengths. The most common barrel length was the 6.5-inch, with 25,660 made. The 7.5-inch had approximately 2,700 made. Lastly, the 10.5-inch had roughly 1,500 made, for a total of 29,860 44 Magnum Flat Tops. The 7.5-inch barreled sixgun was owned by famed gun writer Skeeter Skelton and was one of his favorite field guns. This fact most likely made him responsible for the sales of thousands of Ruger Flat Tops.

Finally, the three-screw Blackhawks started popping up. Mind you, not seeing any three screws didn’t stop me from buying any ‘New Model’ Blackhawks, but we always want what we don’t have. While at a gun show one year, I couldn’t believe my eyes! There on the table, tucked in with all the other Ruger single actions, was a Blackhawk with a 45⁄8-inch barrel. When I nonchalantly asked, “What’s the three screw chambered in?” I about fell over when the reply was, “41 magnum!”

If finding an old three screw was tough, finding a flat-top three-screw Blackhawk seemed nearly impossible. Once again, it happened at my local gun shop. While making my weekly rounds, there it was: a Ruger Flat Top. The gun had been worked over. The barrel was cut back to 5 inches, Skeeter Skelton’s favorite barrel length. It was fitted with a Super Blackhawk hammer, a serrated trigger and a brass Dragoon grip frame. Someone built a Super Blackhawk Flat Top (SBHFT), which was cool, since Ruger never built one.
Because it was altered, I got the SBHFT for much less than an original, which was nice since I really liked how the previous owner built the gun. I eventually swapped out the brass grip frame for an XR3 grip-frame to make the old sixgun easier to carry and conceal. I named my gun “Little Skeet.”

Awarded gunsmith of the year in 2007 by the Guild, Ken’s work is second to none. Ken started by cutting the barrel to 4 inches and finished it off with an 11-degree bull-nose crown, while the ejector rod housing was trimmed flush with the barrel. Ken then shortened the base-pin head, allowing the base-pin to clear the cylinder for removal, without having to remove the ejector rod housing (ERH).


Naturally, the barrel was Mag-Na-Ported for recoil reduction and less muzzle rise.
The action and trigger were worked over to perfection. The trigger breaks at a measured 2 pounds 4 ounces without a hint of creep. I named this gun “Skeeterito.”
For that last final custom touch, I sent the grip-frame to Bobby Tyler to fit some of his beautiful Ram horn stocks. These stocks are perfect and are my favorite sixgun material.

In 2005, Ruger released a mid-frame 50th Anniversary 357 Magnum New Model Blackhawk. It was the same size as the original three-screw Blackhawk. This move had sixgunners licking their chops for a long-awaited. 44 Special on a mid-frame-sized Blackhawk, something custom gunsmiths have been doing since Skeeter Skelton persuaded them to do so in his articles during the late sixties and early seventies.
In 2009, Jason Cloessner, vice president in charge of product design at Lipsey’s, finally made it a reality. By committing to buying a certain number of guns, Ruger agreed to make it happen. The guns sold out in days, and several more runs have been made. The Bisley mid-frame .44 Special has also been added to the line, with many calling it the poor man’s No. 5, in reference to Elmer’s famed sixgun.
I picked up both a 45⁄8-inch and 5.5-inch plow-handled 44 Specials, as well as a 5.5- and 7.5-inch Bisley 44 Specials in the mid-frame guns. These shooters are near and dear to me, as I love the Bisley grip-frame. I sent the 5.5-inch Bisley to Bobby Tyler (TylerGunWorks.com) to work over. He added a Ronnie Wells grip frame and completed an accuracy package before shipping it back. These guns are perfect for all-day shooting events, as recoil is minimal in these configurations.
Amid all this great news about the new model flat tops, Ruger slipped in a 50th Anniversary large-frame 44 Magnum in 2006. So now we have a large-frame New Model Flat Top available in 44 Magnum. I managed to get a limited-run gun, that I love dearly, in 41 Magnum from Williams Supply House around 2009. I’ve kept it original, except for adding some holly stocks, which look like aged ivory from Dick Thompson. I also bought one of the 44 Magnum 50th Anniversary guns and used it for a tribute gun to a special friend, which you will hear in another issue.
It’s funny that the Ruger flat top started with the 357 Magnum, and I don’t have one in either the original three screw, or a new model flat-top. It’s something that needs to be taken care of soon, well – just because. That’s also one of the nice things about sixguns: the next one is out there, waiting for you on the horizon. I sure love my Flat Tops and am thankful Ruger provided us the opportunity to own such fine guns. While the Flat-Top Society doesn’t officially exist, there’s sure enough Ruger flat top lovers out there to justify it.